COMPANY HEADER
Request Information
LVDT gauging sensors are equipped with a plunger and fitted with a return spring. The measuring probe can be interchanged with commercially available measurement probes. Measurement probes are primarily used for the measurement and inspection of work-piece geometries (length, width, diameter, thickness, depth, height, etc.).
Unit of Measure

Specifications

Linearity

 N/A ≤±9 µm

Measuring Range

 N/A ±3 mm

Linearity Full Scale Output (FSO)

 N/A ≤±0.3 %

Repeatability

 N/A ≤0.45 µm

Note for Repeatability

 N/A Averaging over 100 values; 200 repetitions

Temperature Stability Full Scale Output (FSO)

 N/A ≤250 ppm/K

Sensitivity

 N/A 85 mV/mm/V

Excitation Frequency

 N/A 5 kHz

Excitation Voltage

 N/A 550 mV

Connection

 N/A Axial cable outlet Cable diameter of 3.1 mm Integrated cable (3 m) with open ends Minimum bending radii : fixed installation 25 mm, moving 38 mm, drag chain 47 mm

Storage Temperature

 N/A -40 to 80 ºC

Operating Temperature (Without Bellows)

 N/A -20 to 80 ºC

Operating Temperature (With Bellows)

 N/A 0 to 80 ºC

Pressure Resistance

 N/A Atmospheric Pressure

Shock (DIN-EN 60068-2-27)

 N/A 40 g6 ms in 3 axes, 1000 shocks each

Vibration (DIN-EN 60068-2-6)

 N/A ±20 g±1.5 mm10 to 58 Hz in 2 axes, 10 cycles each 58 to 500 Hz in 2 axes, 10 cycles each

Protection Class (DIN-EN 60529)

 N/A Ingress Protection (IP54) (without Bellows) Ingress Protection (IP65) (with Bellows)

Housing Material

 N/A Stainless Steel

Bellows Material

 N/A Fluoroelastomers (FPM)

Cable Sheat Material

 N/A Polyurethane (PUR)

Cable Braids Material

 N/A Polyvinyl Chloride (PVC)/Polypropylene (PP)

Approximate Weight

 N/A 70 g
Typical Spring Forces - Start of Measuring Range (SMR)1 N/A 0.8 N
Typical Spring Forces - Mid of Measuring Range (MMR)2 N/A 1.5 N
Typical Spring Forces - End of Measuring Range (EMR)3 N/A 2.5 N

Compatibility

 N/A MSC7401 MSC7602 MSC7802

Typical Service Life

 N/A 5 million cycles

Dimenison A ( Zero Position)

 N/A 88.2 mm

Dimenison B

 N/A 68.3 mm

Characteristics

Characteristics

 N/A
  • Proven LVDT technology
  • Measuring ranges ±1 … ±10 mm
  • Low cost especially with a large number of pieces
  • Sensor diameter of just ø8mm
  • Models with pneumatic push

Application

Application

 N/A Gauges from Micro-Epsilon have many possible fields of application. Due to different measuring ranges and configuration settings, the gauges are suitable for numerous measurement and inspection tasks. Combined with multi-channel controllers, the DTA gauges are often used for dimensional measurement and inspection tasks, e.g., in automated quality control, R&D and production monitoring.

Additional Information

N/A LVDT gauge sensors DTA-xG8 are primarily used for the measurement and inspection of workpiece geometry (e.g. length, width, diameter, thickness, depth, height). Therefore, different measuring ranges from ±1 mm to ±10 mm are available. The gauges are particularly suitable for applications involving a large number of pieces.

These gauges have an axial cable outlet and are equipped with either a plain bearingguided plunger and a return spring, or with a pneumatic push rod. Depending on the measuring object, different probe tips are available. DTA gauges can be operated with every MSC controller. Depending on this controller, single-/dual-/multi-channel measurements are possible. In addition to the well-established analog output, modern fieldbuses are available for integration purposes.

  • 1 Removing the bellows changes the spring forces.
  • 2 Removing the bellows changes the spring forces.
  • 3 Removing the bellows changes the spring forces.