COMPANY HEADER
Print Back
The LDR-14-Z20 sensors are used for monitoring the clamping position in machine tools. These inductive sensors are integrated in the release device and directly measure the clamping stroke of the drawbar onto which the target ring is glued. Due to their extremely compact design, these sensors are used for different types of tools while providing high-precision and continuous monitoring. No adjustment is necessary when changing the tool.
Unit of Measure

Specifications

Measuring Range

 N/A 14 mm
Resolution for 50 Hertz (Hz) Frequency1 N/A 7 mm
Resolution for 300 Hertz (Hz) Frequency2 N/A 14 mm

Note for Resolution

 N/A Valid when operated with compatible Micro-Epsilon controller.

Typical Linearity ≤±1.5 % Full Scale Output (FSO)

 N/A ≤±0.21 mm

Temperature Stability Full Scale Output (FSO)

 N/A ≤200 ppm/K

Sensitivity

 N/A 26 mV/mm/V

Note for Sensitivity

 N/A With 10 mm reference drawbar.

Excitation Frequency

 N/A 23 kHz

Excitation Voltage

 N/A 550 mV

Measuring Object

 N/A Ring for shaft diameter 8 mm or 10 mm (included in delivery).

Connection

 N/A Axial cable outlet Cable diameter 1.8 mm Integrated cable (2 m) with open ends Minimum bending radius 10 mm (fixed installation)

Storage Temperature

 N/A -40 to 85 ºC

Operating Temperature

 N/A -40 to 120 ºC

Note for Operation Temperature

 N/A Higher temperatures on request.

Pressure Resistance

 N/A Atmospheric Pressure

Shock (DIN-EN 60068-2-27)

 N/A 40 g5 ms, 6 axes, 1000 shocks each

Vibration (DIN-EN 60068-2-6)

 N/A 20 g10 to 49.9 Hz2 mm49.9 Hz - 2000 Hz, 3 axes, 10 cycles each

Protection Class (DIN-EN 60529)

 N/A Ingress Protection (IP67)

Material

 N/A Polyether Ether Ketone (PEEK) Stainless Steel

Approximate Weight (Sensors)

 N/A 30 g

Target Ring Weight

 N/A <1 g

Compatibility

 N/A MSC7401 MSC7602 MSC7802

Typical Service Life

 N/A 5 million cycles

Diameter A (Drawbar D8)

 N/A 8 mm

Diameter B (Drawbar D8)

 N/A 3 mm

Diameter C (Drawbar D8)

 N/A 11.5 mm

Diameter A (Drawbar D10)

 N/A 10 mm

Diameter B (Drawbar D10)

 N/A 5.5 mm

Diameter C (Drawbar D10)

 N/A 11.5 mm

Note for Drawbar

 N/A Not Included in delivery

Characteristics

Characteristics

 N/A
  • Compact design
  • High ambient temperatures
  • High temperature stability
  • High repeatability
  • Robust design IP67

Additional Information

N/A The LDR-14-Z20 sensors are designed for monitoring the clamping position in machine tools.
The cylindrical sensors are integrated into the release device and detect the clamping stroke of the drawbar.
The measuring object is a ring which is glued onto the drawbar. The sensors can be universally used for different types of tools due to their extremely compact sensor design. The sensors provide an analog signal according to the stroke motion of the drawbar when clamping the tool. Consequently, continuous monitoring is possible without the switching point having to be set mechanically.
The miniature sensor controller can either be accommodated at the point of measurement or in the control cabinet. Thanks to their high accuracy, the sensors contribute significantly to meeting the ever increasing requirements for precision and availability of machine tools.

  • 1 Valid when operated with compatible Micro-Epsilon controller.
  • 2 Valid when operated with compatible Micro-Epsilon controller.