COMPANY HEADER
Request Information
optoNCDT 1900 LL laser sensors are designed for the measurement of shiny metallic and rough surfaces. Their small laser line enables precise measurement results with shiny metallic surfaces and structured objects. Due to their extremely compact size, the sensors can also be integrated into restricted installation spaces.
Unit of Measure

Measuring Range

Measurement Range

 N/A 10 mm

Start of Measuring Range (SMR)

 N/A 20 mm

Mid of Measuring Range (MMR)

 N/A 25 mm

End of Measuring Range (EMR)

 N/A 30 mm

Specifications

Measuring Rate

 N/A 1.0 kHz10 kHz2 kHz4 kHz8 kHzContinuously Adjustable between 0.25 to 10 kHz250 Hz500 Hz

Note for Measuring Rate

 N/A 7 Adjustable Stages
Factory setting: measuring rate 4 kHz, median 9; modifying the factory setting requires the IF2001/USB converter.

Linearity

 N/A <±2 µm

Linearity Full Scale Output (FSO)

 N/A <±0.02 %

Note for Linearity

 N/A Relates to digital output

Repeatability

 N/A <0.4 µm

Note for Repeatability

 N/A Typical value with measurements at 4 kHz and median 9
Temperature Stability Full Scale Output (FSO)1 N/A ±0.005 %/K

Light Spot Diameter - Start of Measuring Range (SMR)

 N/A 125 x 730 µm

Light Spot Diameter - Mid of Measuring Range (MMR)

 N/A 55 x 690 µm

Light Spot Diameter - End of Measuring Range (EMR)

 N/A 125 x 660 µm

Light Spot Diameter - Smallest Diameter

 N/A 55 x 690 µm with 25 mm

Note for Light Spot Diameter

 N/A Light spot diameter with line-shaped laser determined based on the emulated 90/10 knife-edge method .

Light Source - Semiconductor Laser Wavelength

N/A 670 nm<1 mW

Light Source Color

 N/A Red

Laser Safety Class

 N/A Class 2 in Accordance with DIN EN 60825-1: 2015-07

Permissible Ambient Light

 N/A 50,000 lux

Direct Current (DC) Supply Voltage

 N/A 11 to 30 V

Power Consumption at 24 Volts (V) Direct Current (DC) Voltage

 N/A <3 W

Signal Input

 N/A 1 x HTL/TTL laser on/off 1 x HTL/TTL multi-function input: trigger in, slave in, zero setting, mastering, teach-in 1 x RS422 synchronization input: trigger in, sync in, master/slave, master/slave alternating

Digital Interface

 N/A EtherNet IP (Connection via interface module) PROFINET (Connection via interface module) RS42

Digital Interface Data Rate

 N/A 18 bits

Analog Output Current

 N/A 4 to 20 mA

Analog Output Voltage

 N/A 0 to 5 V0 to 10 V

Analog Output

 N/A 16 bit, freely scalable within the measuring range

Switching Output

 N/A 2x switching outputs (error & limit value): npn, pnp, push pull

Synchronization

 N/A Possible for simultaneous or alternating measurements

Connection

 N/A Integrated cable 3 m, open ends, min. bending radius 30 mm (fixed installation) Integrated pigtail 0.3 m with 17-pin M12 plug Optional extension to 3 m / 6 m / 9 m / 15 m possible (suitable connection cable/optoNCDT catalog)
Storage Temperature Range2 N/A -20 to 70 ºC
Operation Temperature Range3 N/A 0 to 50 ºC

Shock (DIN-EN 60068-2-29)

 N/A 15 g6 ms in 3 Axes

Vibration (DIN-EN 60068-2-6)

 N/A 20 g20 to 500 Hz

Protection Class (DIN-EN 60529)

 N/A Ingress Protection (IP67)

Housing Material

 N/A Aluminum

Approximate Weight with Pigtail

 N/A 185 g

Approximate Weight with Cable

 N/A 300 g

Control and Display Element

 N/A 2 x color LEDs for power/status Select & function keys: interface selections, mastering (zero), teach, presets, quality slider, frequency selection, factory settings web interface for setup (Connection to PC via IF2001/USB): application-specific presets, peak selection, video signal, freely selectable averaging possibilities, data reduction, setup management

Dimensions

Dimension X

 N/A 33 mm

Dimension Y

 N/A 14 mm

Characteristics

Characteristics

 N/A
  • Precise laser sensor with oval-shaped light spot (laser line)
  • For shiny metallic, rough and structured surfaces
  • Unique combination of compact size, high speed and accuracy
  • Ideal for static and dynamic measurements with high resolution
  • Highest ambient light resistance in its class
  • Advanced Surface Compensation for high speed measurements on changing surfaces

Additional Information

N/A The optoNCDT LL laser sensors produce an oval-shaped light spot of just a few millimeters in width which reminds of a short laser line (LL). This oval light spot compensates for inhomogeneous surface structures and the so-called speckling effect which particularly occurs with metallic surfaces. Combined with special software algorithms, interferences caused by surface roughness, defects, indentations or holes are filtered out. This enables stable and precise measurement results.

Laser sensors with oval-shaped light spot (laser line)

The optoNCDT 1900LL is the latest Micro-Epsilon laser sensor. This innovative sensor projects an oval-shaped light spot which reminds of a short laser line (LL). The laser sensor impresses with precise distance measurements on shiny metallic and structured surfaces, as well as materials where the laser beam penetrates. The integrated high-performance controller enables fast and highly precise processing and output of measurement values. The innovative optoNCDT 1900LL laser triangulation sensor is used wherever high precision and reliability are required, e.g., in challenging automation tasks, automotive production, 3D printing and in measuring machines.

Advanced Surface Compensation The intelligent exposure control for demanding surfaces

The optoNCDT 1900LL is equipped with an intelligent surface control feature. New algorithms generate stable measurement results even on demanding surfaces where changing reflections occur. In addition, the sensor has the highest resistance to ambient light in its class and can be used in strongly illuminated environments up to 50,000 lux.

  • 1 Relates to digital output in mid of measuring range.
  • 2 Non-condensing
  • 3 Non-condensing